CAN-Open Multi-drop Bus Fiber Optic Converter

Descriptions:

The HFD-FO-OPE CAN Open Fiber Optic series products provide an optical point-to-point or bus network connection for CAN Open data interfaces on one or two, multimode or singlemode optical fibers. The CAN Open Point-to-Point Transmission units operate as the end or terminal points and provide an electrical connection and a two fibre optical connection. The units support CAN 1.0 and CAN 2.0 CAN standards, and Device Net. And are transparent to all high level protocols.

This series is available in either wall mount, DIN rail or 3U chassis card configurations.

Product Features of the CanOpen Fiber Optic Converter
Up to 1MB data rate
Multi mode and single mode
Single fiber solution
Wall mount, rack or chassis configurations
Product Features
Up to 1Mbps data rate
Multi mode and single mode
Single fiber solution,Dual power supplies

Other specs of the CANOpen BUS Fiber Optic Converter

Ordering Information:

CanOpen Protocol Repeater

The CANOpen Repeater is a kind of protocol bridge repeater,which is used to prolong the distance of CANOpen communication,increase the nodes and improve the isolation ability.The repeater is based on industrial grade and it has low power consumption and easy mount way.When the CANOpen repeater connects 2 CANOpen networks,the 2 networks work at the same rate,the system has auto-sensing function.The CANOpen repeater uses 5 PIN block terminal interface,which is in compliance with CANOpen standard.

Technical Specification:

Bus Topology: Point to point link

Flow control function: Yes

CANOpen Bus Interface: 5 PIN block terminal,in compliance with European standard

Transmission Type: Prototocl, CAN frame transmission

CAN standard：CAN2.0A、CAN2.0B

CANOpen Baud Rate：10Kbps、20Kbps、50Kbps、62.5Kbps、100Kbps、125Kbps、250Kbps、

500Kbps、800Kbps、1000Kbps；Auto-sensing

Buffering： 128 frames buffer

Power Input：DC9V-DC30V， < 2W ；

LED Status：Data，Power,Work status，Alarm

Dry Contact Alarm Output：Relay Interface，24V@1A,This email address is being protected from spambots. You need JavaScript enabled to view it.

Housing：D35mm DIN Rail，40x 110 x 74（mm）

Enclosure：Metal：IP40

Vibration：In compliance with IEC68-2-6

Weight：600g

Work Temperature:-25℃ ~ +75℃；Humidity：95% No condensing；

Storage：-45℃ ~ +85℃

Standard：CANOpen Standard

Electromagnetic：EN61000-4-2（8KV ESD）

EN61000-4-3，ENV50204（anti-electromagnetic 10V/m at 10KHz-1GHz）

EN61000-4-4（2KV Fast pulse group）

EN61000-4-5（Common mode 1KV，Differential mode 2KV SPD）

EN55022（Radiation class B）

CAN-Open Fiber Optic Converter

Descriptions:

The HFD-FO-OPE CAN Open Fiber Optic series products provide an optical point-to-point or bus network connection for CAN Open data interfaces on one or two, multimode or singlemode optical fibers. The CAN Open Point-to-Point Transmission units operate as the end or terminal points and provide an electrical connection and a two fibre optical connection. The units support CAN 1.0 and CAN 2.0 CAN standards, and Device Net. And are transparent to all high level protocols.

This series is available in either wall mount, DIN rail or 3U chassis card configurations.

Product Features of the CanOpen Fiber Optic Converter
Up to 1MB data rate
Multi mode and single mode
Single fiber solution
Wall mount, rack or chassis configurations
Product Features
Up to 1Mbps data rate
Multi mode and single mode
Single fiber solution,Dual power supplies

Other specs of the CANOpen Fiber Optic Converter

Ordering Information: