CAN FD to Ethernet Converter(CANFD-NET-100T/200T)

1.1 Product Overview

CAN-FD-NET-100T/200T high performance CAN FD to Ethernet converter integrates one CAN (FD) interface or two-way CAN FD interfaces and Ethernet interface as well as TCP / IP protocol stack. Users can easily realize the interconnection and interworking between CAN bus network and Ethernet network, and further expand the scope of CAN FD network.

CAN-FD-NET-100T / 200T CAN FD to Ethernet adapter, each CAN channel is integrated with complete electrical isolation protection and surge protection, with strong anti-interference ability. It is a CAN FD over Ethernet converter with stable performance and reliable communication.

The conversion efficiency of CAN-FD-NET-100T / 200T adapter reaches 5000 frames / S (CAN FD extended frames at 5Mbps), which is suitable for all applications of CAN (FD) from low speed to high speed.

1.2 Product Features:

• 32-bit 400m processor with embedded real-time operating system.
• The flow rate is 5000 frames / S (CAN FD extended frames at 5Mbps).
• Using real-time operating system and adaptive flow control algorithm, it is suitable for the control system with strict real-time requirements.
• CAN (FD) - bus interface adopts electromagnetic isolation with isolation voltage of 2.5KV.
• 10m / 100M Ethernet interface (RJ45), 2KV electromagnetic isolation;
• Configuration software can be used to set the working parameters of CAN (FD) and Ethernet.
• CAN 2.0A and CAN 2.0B protocols.
• It supports 1-2 CAN (FD) controllers, and each channel can be controlled separately.
• Shielded or unshielded twisted pair.
• The baud rate of CAN (FD) controller is between 5 Kbps and 5 Mbps.
• At most 110 nodes can be connected to a single bus, and the longest communication distance is 10 km.
• 9-40V DC wide voltage input with surge, over-current and reverse connection protection.
• Working temperature: - 40 ℃ - + 85 ℃.
• Storage temperature: - 55 ℃ - + 85 ℃.
• Physical size: (length) 105mm * (width) 84mm * (height) 28mm. 
• Can Bus port number: 1 or 2

1.3 Typical applications

CAN-bus network diagnosis and test

Auto electronic applications

Electric power communication network

Industrial control devices

High-speed and large data communications

Ordering Information:

CAN Bus to Ethernet Converter(BUE-CANET-I & BUE-CANET-II)

1.1 Product Overview

Our CAN Bus to Ethernet converter  is  an intelligent  CAN bus communication  interface  that  is compatible  with  TCP/IP protocol and supports one or two CAN channel. Using this module will enable PC to connect to CAN-bus network via USB bus, forming the CAN-bus network control nodes for the data processing and data collection for the CAN-bus networks such as bus laboratory, industrial control, intelligent residential zone, auto electronics network, and etc.

CAN Bus to Ethernet gateway comes with an electrical isolation module, which could be used to avoid the damage caused by the ground loop and enhance the system reliability when working under a tough environment.

Our CAN Bus to Ethernet converter can  use  our  Tester  software provided  by us  to  directly finish  CAN  Bus message sending, and receiving.

1.2 Parameters

Application as Ethernet based interface to the CAN bus Microcontroller STR912FAW44X6(ARM9 Based) Ethernet 10M/100M

Baud rates up to 1MB & 7500 frames.

CAN 2.0A (11-bit ID standard frames) and 2.0B (29-bit ID extended frames) Config software available through the Ethernet interface.

Comply with ISO-11898.

Examples of Visual C++, C++Builder are available; Max data flow 6000PS (extend frame)

Operating temperature: -20 to +70

Physical size: (length) 105mm * (width) 84mm * (height) 28mm. Powered by DC (7 to 40V)

Can Bus port number: 1 or 2

1.3 Typical applications

CAN-bus network diagnosis and test

Auto electronic applications

Electric power communication network

Industrial control devices

High-speed and large data communications

Ordering Information: